home *** CD-ROM | disk | FTP | other *** search
/ QRZ! Ham Radio 5 / QRZ Ham Radio Callsign Database - Volume 5.iso / files / tcpip / amiga / akit29m.lha / AmigaNOS / TCPIP / Digger / ALINCO.LHA / ALINCO.LIT < prev    next >
Encoding:
Text File  |  1992-11-15  |  2.2 KB  |  65 lines

  1.               ALINCO DR-110 LCD READOUT REPAIR
  2.               ================================
  3.  
  4. This should also work for the DR-112 and DR-410
  5.  
  6. Tools needed
  7.  
  8. Low power solder pencil or solder station
  9. Solder wick or de-solder station
  10. Small dykes
  11. Small needle-nose pliers
  12. Hemostats
  13. Small/medium Philips screwdriver
  14. Solder
  15.  
  16. 6 grain-of-wheat lights from Alinco or Radio Shack part no.272-1141 12Vdc
  17. .025A
  18. (the Radio Shack parts have nice pigtails on them and you do not need the
  19.  yellow sleeves for them.  Alternatively, use Radio Shack part no. 272-1092
  20.  12Vdc 60mA micro lamps.  These do not have the insulated pigtails on them
  21.  but are brighter).
  22.  
  23. 1 - Remove top and bottom covers
  24.  
  25. 2 - Remove 3 knobs from the front of the radio
  26.  
  27. 3 - Remove nut from shaft of the channel selector
  28.  
  29. 4 - Remove nut from the microphone connector
  30.  
  31. 5 - Remove front plate from radio.  This has plastic snap clips top and
  32.     bottom, so take care.
  33.  
  34. 6 - Remove 3 small philips screws holding the PCB to the front of the radio.
  35.     Do not cut wires.
  36.  
  37. 7*- Locate tabs that are holding the display to the PCB and bend them
  38.     straight.  Take care not to break them off.
  39.  
  40. 8*- Remove display from PCB and set aside.
  41.  
  42. *  Steps 7 and 8 can be omitted if you can locate the two display lights
  43.    from the back of the PCB.
  44.  
  45. 9 - Locate lights (6). 1 is under the on/off switch, 3 are above the row of
  46.     small switches.  All 4 have a blue rubber cover on them.  2 lights are
  47.     mounted where the LCD display was.
  48.  
  49. 10- Replace the lights using care and remember to replace the blue covers on
  50.     those which had them in the first instance.  Remember to replace the
  51.     yellow sleeving on the lights which illuminate the LCD.
  52.  
  53. 11- Re-install the LCD display, ensuring there is no contamination of the
  54.     contacts on either the LCD or the PCB.  Using the tabs, ensure the LCD is
  55.     tight to the PCB otherwise the contact will be poor, resulting in missing
  56.     segments on the display.
  57.  
  58. 12- Test the display by powering up the radio before complete reassembly.
  59.  
  60. 13- Reset the CPU as per the owner's manual.  This is a precaution as the CPU
  61.     is located on the board you have been working on.
  62.  
  63. 73 Frank N2JYG @ WA0PTV.#WNY.NY.USA.NOAM
  64.  
  65.